服务搜索 SEARCH
ASTM F2115
作者:TECERT    发布于:2014-04-27 09:53:44    检测认证一站式服务    收藏:Ctrl+D
摘要:ASTM F2115 Standard Specification for Motorized Treadmills 联系我们:info@tecert.com 安排检测 / Contact us for testing.

标准编号 Standard/Code 标准名称 Standard Title
ASTM F2115 Standard Specification for Motorized Treadmills

This specification covers the establishment of parameters for the design and manufacture of motorized treadmills. The treadmill shall be stable during intended use. Its edges in accessible areas shall be free of burrs and sharp edges and its corners in accessible areas shall be radiused or chamfered. Its tube ends in the exposed accessible areas shall be closed off either by other components or plugs, caps, or covers. In addition, the design of rotating parts shall avoid shear, pinch, or catch points by guarding, shielding, spacing, or other appropriate means. To reduce the risk of finger entrapment, the rear roller of the treadmill shall be designed or guarded. The guard or design shall function through the full range of inclination possible and through the full range of belt tension adjustment. Foot rails and handrails shall be present in all treadmills to facilitate user mounting and dismounting. Its moving surface shall be constructed to minimize foot slippage. The control panel for the operation of the treadmill shall be readily accessible by the user. The controls for a motorized treadmill shall incorporate a prominently labeled and user accessible stop switch. The stop switch causes the moving surface to decelerate and stop and stops the motion of any power-driven incline system. Stop mechanisms may include a push-button stop switch, a pull cord stop switch, an infrared beam switch, or other suitable means. Adequate warnings alerting users, third parties, and service personnel to hazards associated with treadmills shall be provided.

This abstract is a brief summary of the referenced standard. It is informational only and not an official part of the standard; the full text of the standard itself must be referred to for its use and application. ASTM does not give any warranty express or implied or make any representation that the contents of this abstract are accurate, complete or up to date.

1. Scope

1.1 This specification covers the establishment of parameters for the design and manufacture of motorized treadmills.

1.2 It is the intent of this specification to specify products for use by individuals age 13 and above.

1.3 This standard is to be used in conjunction with Specification F2276, Test Methods F2571, and Test Methods F2106.

1.4 This standard takes precedence over Specification F2276 and Test Methods F2571 in areas that are specific to motorized treadmills.

1.5 This specification2 establishes additional requirements not set forth in the referenced ASTM standards for the design of commercial fitness equipment to increase access and user independence by people with functional limitations or impairments.

1.6 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only.

1.7 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.8 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

ASTM F2115

Test Item 测试名称: ASTM F2115 Motorized Treadmills 跑步机
 
Test Requirements 测试要求:

4.2 Stability
4.3 Exterior Design
4.4 Endurance
4.5 Static Loading
4.6 Overheating
4.7 Adjustable Incline System
4.8 Control Panel
4.9 Motorized Drive System Operation
5 Warnings/Warning Labels
6 Documentation

Sample Size 样品数量 / 送样规格: 3 sets / 3套
Lead Time / TAT (Turn Around Time) 测试周期: 常规服务 Regular service 25 working days

Report Summary 报告摘要:

 

脚注信息
 ©2013-2024 TECERT ≥ TEST & CERTIFICATION 特色检测 - 检测认证搜索引擎 粤ICP备13066711号-2  beian 粤公网安备 44030702000495号  ❤️ 机构 ❤️
访问统计