服务搜索 SEARCH
ASTM E162
作者:TECERT    发布于:2014-04-27 09:46:06    检测认证一站式服务    收藏:Ctrl+D
摘要:ASTM E162 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source 联系我们:info@tecert.com 安排检测 / Contact us for testing.

标准编号 Standard/Code 标准名称 Standard Title
ASTM E162 Standard Test Method for Surface Flammability of Materials Using a Radiant Heat Energy Source

5.1 This test method provides a laboratory test procedure for measuring and comparing the surface flammability of materials when exposed to a prescribed level of radiant heat energy. It is intended for use in measurements of the surface flammability of materials exposed to fire. The test is conducted using small specimens that are representative, to the extent possible, of the material or assembly being evaluated. (Example: in terms of their thickness, layering, and any potential substrate.)

5.2 The rate at which flames will travel along surfaces depends upon the physical and thermal properties of the material, product or assembly under test, the specimen mounting method and orientation, the type and level of fire or heat exposure, the availability of air, and properties of the surrounding enclosure.4

5.3 In this procedure, the specimens are subjected to one or more specific sets of laboratory fire test conditions. If different test conditions are substituted or the end-use conditions are changed, it is not always possible by or from this test to predict changes in the fire-test-response characteristics measured. Therefore, the results are valid only for the fire test exposure conditions described in this procedure.

5.4 If the test results obtained by this test method are to be considered as part of an overall assessment of fire hazard in a building or structure, then the example criteria, concepts and procedures incorporated into Guide E1546 shall be taken into consideration.

1. Scope

1.1 This fire-test-response standard describes the measurement of surface flammability of materials. It is not intended for use as a basis of ratings for building code purposes (see Appendix X1).

1.2 The values stated in inch-pound units are to be regarded as standard. The values given in parentheses are mathematical conversions to SI units that are provided for information only and are not considered standard.

1.3 This standard measures and describes the response of materials, products, or assemblies to heat and flame under controlled conditions, but does not by itself incorporate all factors required for fire hazard or fire risk assessment of the materials, products, or assemblies under actual fire conditions.

1.4 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

1.5 Fire testing of products and materials is inherently hazardous, and adequate safeguards for personnel and property shall be employed in conducting these tests. This test method may involve hazardous materials, operations, and equipment. Specific information about hazard is given in Section .

Note 1: There is no similar or equivalent ISO standard.

Test Requirement 测试要求:

1)试样数量最少需要4组,由于标准要求最少要4组有效的试验结果,所以为了安全起见,最好提供8组。
2)Materials intended to be applied to a substrate shall be tested on that substrate.对于在实际应用中有确定的应用基材,测试中应该应用到这种指定的基材上。
3)Flexible materials shall be cut to 10 by 22-in. (255 by 560-mm),对于软质材料,提供尺寸为255 by 560-mm。

Sample Size 样品数量 / 送样规格: 8 pieces, 6’"(152mm) wide by 18”(457mm) long by maximum 1” (25.4mm) thickness,8 片152mm×457mm×实际厚度(一般不大于25.4mm)
Lead Time / TAT (Turn Around Time) 测试周期: 常规服务 Regular service 9 working days

Report Summary 报告摘要:

 

脚注信息
 ©2013-2024 TECERT ≥ TEST & CERTIFICATION 特色检测 - 检测认证搜索引擎 粤ICP备13066711号-2  beian 粤公网安备 44030702000495号  ❤️ 机构 ❤️
访问统计