服务搜索 SEARCH
ASTM E2149
作者:TECERT    发布于:2014-04-23 16:38:12    检测认证一站式服务    收藏:Ctrl+D
摘要:ASTM E2149 Standard Test Method for Determining the Antimicrobial Activity of Antimicrobial Agents Under Dynamic Contact Conditions 联系我们:info@tecert.com 安排检测 / Contact us for testing.

标准编号 Standard/Code 标准名称 Standard Title
ASTM E2149 Standard Test Method for Determining the Antimicrobial Activity of Antimicrobial Agents Under Dynamic Contact Conditions

5.1 Substrate–bonded, antimicrobial agents are not typically free to diffuse into their environment under normal conditions of use. This test method ensures good contact between the bacteria and the treated fiber, fabric, or other substrate, by constant agitation of the test specimen in a challenge suspension during the test period.

5.2 The metabolic state of the challenge species can directly affect measurements of the effectiveness of particular antimicrobial agents or concentrations of agents. The susceptibility of the species to particular biocides could be altered depending on its life stage (cycle). One-hour contact time in a buffer solution allows for metabolic stasis in the population. This test method standardizes both the growth conditions of the challenge species and substrate contact times to reduce the variability associated with growth phase of the microorganism.

5.3 Leaching of an antimicrobial is dependent upon the test conditions being utilized and the ultimate end use of the product. Additional testing may be required to determine if a compound is substrate-bound in all conditions or during the end use of the product.

5.4 This test method cannot determine if a compound is leaching into solution or is immobilized on the substrate. This test method is only intended to determine efficacy as described in subsequent portions of the method.

5.5 The test is suitable for evaluating stressed or modified specimens, when accompanied by adequate controls.

NOTE 1: Stresses may include laundry, wear and abrasion, radiation and steam sterilization, UV exposure, solvent manipulation, temperature susceptibility, or similar physical or chemical manipulation.

1. Scope

1.1 This test method is designed to evaluate the antimicrobial activity of antimicrobial-treated specimens under dynamic contact conditions. This dynamic shake flask test was developed for routine quality control and screening tests in order to overcome difficulties in using classical antimicrobial test methods to evaluate substrate-bound antimicrobials. These difficulties include ensuring contact of inoculum to treated surface (as in AATCC TM100), flexibility of retrieval at different contact times, use of inappropriately applied static conditions (as in AATCC TM147), sensitivity, and reproducibility.

1.2 This test method allows for the ability to evaluate many different types of treated substrates and a wide range of microorganisms. Treated substrates used in this test method can be subjected to a wide variety of physical/chemical stresses or manipulations and allows for the versatility of testing the effect of contamination due to such things as hard water, proteins, blood, serum, various chemicals, and other contaminants.

1.3 Surface antimicrobial activity is determined by comparing results from the test sample to controls run simultaneously.

1.4 This test method may not be appropriate for all types of antimicrobial-treated articles or antimicrobial agents. The proper test methodology should be determined based on antimicrobial mode of action and end-use expectations (Guide E2922)

1.5 Proper neutralization of all antimicrobials must be confirmed using Test Methods E1054.

1.6 This test method should be performed only by those trained in microbiological techniques.

1.7 The values stated in SI units are to be regarded as standard. No other units of measurement are included in this standard.

1.8 This standard may involve hazardous materials, operations and equipment. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety, health, and environmental practices and determine the applicability of regulatory limitations prior to use.

1.9 This international standard was developed in accordance with internationally recognized principles on standardization established in the Decision on Principles for the Development of International Standards, Guides and Recommendations issued by the World Trade Organization Technical Barriers to Trade (TBT) Committee.

Test Item 测试名称: ASTM E2149 Antimicrobial Activity 抗菌检测

Test Requirement 测试要求:

ASTM E2149 Determining the Antimicrobial Activity of Immobilized Antimicrobial Agents Under Dynamic Contact Conditions 测​定​动​态​接​触​条​件​下​固​定​化​抗​菌​剂​抗​微​生​物​活​性​的​试​验​方​法
ATCC 25922 Escherichia coli 大肠埃希氏菌(E. coli)常称为大肠杆菌
ATCC 6538 Staphylococcus aureus 金黄色葡萄球菌
AS1.1194 Salmonella typhimurium 鼠伤寒沙门氏菌

Sample Size 样品数量 / 送样规格: 40g
Lead Time / TAT (Turn Around Time) 测试周期: 常规服务 Regular service 9 working days

Report Summary 报告摘要:

 

脚注信息
 ©2013-2024 TECERT ≥ TEST & CERTIFICATION 特色检测 - 检测认证搜索引擎 粤ICP备13066711号-2  beian 粤公网安备 44030702000495号  ❤️ 机构 ❤️
访问统计